"LCD" redirects here. For other uses, see LCD (disambiguation)
Not to be confused with LED
Layers of a reflective twisted nematic liquid crystal display:
A liquid-crystal display (LCD) is a flat-panel display or other electronically modulated optical device that uses the light-modulating properties of liquid crystals combined with polarizers to display information. Liquid crystals do not emit light directly[1] but instead use a backlight or reflector to produce images in color or monochrome.[2]
LCDs are available to display arbitrary images (as in a general-purpose computer display) or fixed images with low information content, which can be displayed or hidden: preset words, digits, and seven-segment displays (as in a digital clock) are all examples of devices with these displays. They use the same basic technology, except that arbitrary images are made from a matrix of small pixels, while other displays have larger elements.
LCDs can either be normally on (positive) or off (negative), depending on the polarizer arrangement. For example, a character positive LCD with a backlight has black lettering on a background that is the color of the backlight, and a character negative LCD has a black background with the letters being of the same color as the backlight.
LCDs are used in a wide range of applications, including LCD televisions, computer monitors, instrument panels, aircraft cockpit displays, and indoor and outdoor signage. Small LCD screens are common in LCD projectors and portable consumer devices such as digital cameras, watches, calculators, and mobile telephones, including smartphones. LCD screens have replaced heavy, bulky and less energy-efficient cathode-ray tube (CRT) displays in nearly all applications.
LCDs are not subject to screen burn-in like on CRTs. However, LCDs are still susceptible to image persistence.[3]
[
edit
]
An LCD screen used as a notification panel for travellersEach pixel of an LCD typically consists of a layer of molecules aligned between two transparent electrodes, often made of indium tin oxide (ITO) and two polarizing filters (parallel and perpendicular polarizers), the axes of transmission of which are (in most of the cases) perpendicular to each other. Without the liquid crystal between the polarizing filters, light passing through the first filter would be blocked by the second (crossed) polarizer. Before an electric field is applied, the orientation of the liquid-crystal molecules is determined by the alignment at the surfaces of electrodes. In a twisted nematic (TN) device, the surface alignment directions at the two electrodes are perpendicular to each other, and so the molecules arrange themselves in a helical structure, or twist. This induces the rotation of the polarization of the incident light, and the device appears gray. If the applied voltage is large enough, the liquid crystal molecules in the center of the layer are almost completely untwisted and the polarization of the incident light is not rotated as it passes through the liquid crystal layer. This light will then be mainly polarized perpendicular to the second filter, and thus be blocked and the pixel will appear black. By controlling the voltage applied across the liquid crystal layer in each pixel, light can be allowed to pass through in varying amounts thus constituting different levels of gray.
The chemical formula of the liquid crystals used in LCDs may vary. Formulas may be patented.[4] An example is a mixture of 2-(4-alkoxyphenyl)-5-alkylpyrimidine with cyanobiphenyl, patented by Merck and Sharp Corporation. The patent that covered that specific mixture has expired.[5]
Most color LCD systems use the same technique, with color filters used to generate red, green, and blue subpixels. The LCD color filters are made with a photolithography process on large glass sheets that are later glued with other glass sheets containing a thin-film transistor (TFT) array, spacers and liquid crystal, creating several color LCDs that are then cut from one another and laminated with polarizer sheets. Red, green, blue and black colored photoresists (resists) are used to create color filters. All resists contain a finely ground powdered pigment, with particles being just 40 nanometers across. The black resist is the first to be applied; this will create a black grid (known in the industry as a black matrix) that will separate red, green and blue subpixels from one another, increasing contrast ratios and preventing light from leaking from one subpixel onto other surrounding subpixels.[6] After the black resist has been dried in an oven and exposed to UV light through a photomask, the unexposed areas are washed away, creating a black grid. Then the same process is repeated with the remaining resists. This fills the holes in the black grid with their corresponding colored resists.[7][8][9] Black matrices made in the s and s when most color LCD production was for laptop computers, are made of Chromium due to its high opacity, but due to environmental concerns, manufacturers shifted to black colored photoresist with carbon pigment as the black matrix material.[10][11][12] Another color-generation method used in early color PDAs and some calculators was done by varying the voltage in a Super-twisted nematic LCD, where the variable twist between tighter-spaced plates causes a varying double refraction birefringence, thus changing the hue.[13] They were typically restricted to 3 colors per pixel: orange, green, and blue.[14]
LCD in a Texas Instruments calculator with top polarizer removed from device and placed on top, such that the top and bottom polarizers are perpendicular. As a result, the colors are inverted.The optical effect of a TN device in the voltage-on state is far less dependent on variations in the device thickness than that in the voltage-off state. Because of this, TN displays with low information content and no backlighting are usually operated between crossed polarizers such that they appear bright with no voltage (the eye is much more sensitive to variations in the dark state than the bright state). As most of -era LCDs are used in television sets, monitors and smartphones, they have high-resolution matrix arrays of pixels to display arbitrary images using backlighting with a dark background. When no image is displayed, different arrangements are used. For this purpose, TN LCDs are operated between parallel polarizers, whereas IPS LCDs feature crossed polarizers. In many applications IPS LCDs have replaced TN LCDs, particularly in smartphones. Both the liquid crystal material and the alignment layer material contain ionic compounds. If an electric field of one particular polarity is applied for a long period of time, this ionic material is attracted to the surfaces and degrades the device performance. This is avoided either by applying an alternating current or by reversing the polarity of the electric field as the device is addressed (the response of the liquid crystal layer is identical, regardless of the polarity of the applied field).
A Casio Alarm Chrono digital watch with LCDDisplays for a small number of individual digits or fixed symbols (as in digital watches and pocket calculators) can be implemented with independent electrodes for each segment.[15] In contrast, full alphanumeric or variable graphics displays are usually implemented with pixels arranged as a matrix consisting of electrically connected rows on one side of the LC layer and columns on the other side, which makes it possible to address each pixel at the intersections. The general method of matrix addressing consists of sequentially addressing one side of the matrix, for example by selecting the rows one-by-one and applying the picture information on the other side at the columns row-by-row. For details on the various matrix addressing schemes see passive-matrix and active-matrix addressed LCDs.
[
edit
]
LCDs are manufactured in cleanrooms borrowing techniques from semiconductor manufacturing and using large sheets of glass whose size has increased over time. Several displays are manufactured at the same time, and then cut from the sheet of glass, also known as the mother glass or LCD glass substrate. The increase in size allows more displays or larger displays to be made, just like with increasing wafer sizes in semiconductor manufacturing. The glass sizes are as follows:
Until Gen 8, manufacturers would not agree on a single mother glass size and as a result, different manufacturers would use slightly different glass sizes for the same generation. Some manufacturers have adopted Gen 8.6 mother glass sheets which are only slightly larger than Gen 8.5, allowing for more 50- and 58-inch LCDs to be made per mother glass, specially 58-inch LCDs, in which case 6 can be produced on a Gen 8.6 mother glass vs only 3 on a Gen 8.5 mother glass, significantly reducing waste.[22] The thickness of the mother glass also increases with each generation, so larger mother glass sizes are better suited for larger displays. An LCD module (LCM) is a ready-to-use LCD with a backlight. Thus, a factory that makes LCD modules does not necessarily make LCDs, it may only assemble them into the modules. LCD glass substrates are made by companies such as AGC Inc., Corning Inc., and Nippon Electric Glass.
[
edit
]
The origin and the complex history of liquid-crystal displays from the perspective of an insider during the early days were described by Joseph A. Castellano in Liquid Gold: The Story of Liquid Crystal Displays and the Creation of an Industry.[7] Another report on the origins and history of LCD from a different perspective until has been published by Hiroshi Kawamoto, available at the IEEE History Center.[27] A description of Swiss contributions to LCD developments, written by Peter J. Wild, can be found at the Engineering and Technology History Wiki.[28]
[
edit
]
In ,[29] Friedrich Reinitzer (&#;) discovered the liquid crystalline nature of cholesterol extracted from carrots (that is, two melting points and generation of colors) and published his findings.[30] In , Otto Lehmann published his work "Flüssige Kristalle" (Liquid Crystals). In , Charles Mauguin first experimented with liquid crystals confined between plates in thin layers.
In , Georges Friedel described the structure and properties of liquid crystals and classified them in three types (nematics, smectics and cholesterics). In , Vsevolod Frederiks devised the electrically switched light valve, called the Fréedericksz transition, the essential effect of all LCD technology. In , the Marconi Wireless Telegraph company patented the first practical application of the technology, "The Liquid Crystal Light Valve". In , the first major English language publication Molecular Structure and Properties of Liquid Crystals was published by Dr. George W. Gray.[31] In , Richard Williams of RCA found that liquid crystals had some interesting electro-optic characteristics and he realized an electro-optical effect by generating stripe patterns in a thin layer of liquid crystal material by the application of a voltage. This effect is based on an electro-hydrodynamic instability forming what are now called "Williams domains" inside the liquid crystal.[32]
Building on early MOSFETs, Paul K. Weimer at RCA developed the thin-film transistor (TFT) in .[33] It was a type of MOSFET distinct from the standard bulk MOSFET.[34]
[
edit
]
In , George H. Heilmeier, who was working at the RCA laboratories on the effect discovered by Richard Williams, achieved the switching of colors by field-induced realignment of dichroic dyes in a homeotropically oriented liquid crystal. Practical problems with this new electro-optical effect made Heilmeier continue to work on scattering effects in liquid crystals and finally the achievement of the first operational liquid-crystal display based on what he called the dynamic scattering mode (DSM). Application of a voltage to a DSM display switches the initially clear transparent liquid crystal layer into a milky turbid state. DSM displays could be operated in transmissive and in reflective mode but they required a considerable current to flow for their operation.[35][36][37][38] George H. Heilmeier was inducted in the National Inventors Hall of Fame[39] and credited with the invention of LCDs. Heilmeier's work is an IEEE Milestone.[40]
Demonstration digital clock made in using then recently developed Cyanobiphenyl liquid crystalsIn the late s, pioneering work on liquid crystals was undertaken by the UK's Royal Radar Establishment at Malvern, England. The team at RRE supported ongoing work by George William Gray and his team at the University of Hull who ultimately discovered the cyanobiphenyl liquid crystals, which had correct stability and temperature properties for application in LCDs.[41]
The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in .[42] Lechner, F.J. Marlowe, E.O. Nester and J. Tults demonstrated the concept in with an 18x2 matrix dynamic scattering mode (DSM) LCD that used standard discrete MOSFETs.[43]
[
edit
]
On December 4, , the twisted nematic field effect (TN) in liquid crystals was filed for patent by Hoffmann-LaRoche in Switzerland, (Swiss patent No. 532 261 Archived March 9, , at the Wayback Machine) with Wolfgang Helfrich and Martin Schadt (then working for the Central Research Laboratories) listed as inventors.[35] Hoffmann-La Roche licensed the invention to Swiss manufacturer Brown, Boveri & Cie, its joint venture partner at that time, which produced TN displays for wristwatches and other applications during the s for the international markets including the Japanese electronics industry, which soon produced the first digital quartz wristwatches with TN-LCDs and numerous other products. James Fergason, while working with Sardari Arora and Alfred Saupe at Kent State University Liquid Crystal Institute, filed an identical patent in the United States on April 22, .[44] In , the company of Fergason, ILIXCO (now LXD Incorporated), produced LCDs based on the TN-effect, which soon superseded the poor-quality DSM types due to improvements of lower operating voltages and lower power consumption. Tetsuro Hama and Izuhiko Nishimura of Seiko received a US patent dated February , for an electronic wristwatch incorporating a TN-LCD.[45] In , the first wristwatch with TN-LCD was launched on the market: The Gruen Teletime which was a four digit display watch.
In , the concept of the active-matrix thin-film transistor (TFT) liquid-crystal display panel was prototyped in the United States by T. Peter Brody's team at Westinghouse, in Pittsburgh, Pennsylvania.[46] In , Brody, J. A. Asars and G. D. Dixon at Westinghouse Research Laboratories demonstrated the first thin-film-transistor liquid-crystal display (TFT LCD).[47][48] As of , all modern high-resolution and high-quality electronic visual display devices use TFT-based active matrix displays.[49] Brody and Fang-Chen Luo demonstrated the first flat active-matrix liquid-crystal display (AM LCD) in , and then Brody coined the term "active matrix" in .[42]
In North American Rockwell Microelectronics Corp introduced the use of DSM LCDs for calculators for marketing by Lloyds Electronics Inc, though these required an internal light source for illumination.[50] Sharp Corporation followed with DSM LCDs for pocket-sized calculators in [51] and then mass-produced TN LCDs for watches in .[52] Other Japanese companies soon took a leading position in the wristwatch market, like Seiko and its first 6-digit TN-LCD quartz wristwatch, and Casio's 'Casiotron'. Color LCDs based on Guest-Host interaction were invented by a team at RCA in .[53] A particular type of such a color LCD was developed by Japan's Sharp Corporation in the s, receiving patents for their inventions, such as a patent by Shinji Kato and Takaaki Miyazaki in May ,[54] and then improved by Fumiaki Funada and Masataka Matsuura in December .[55] TFT LCDs similar to the prototypes developed by a Westinghouse team in were patented in by a team at Sharp consisting of Fumiaki Funada, Masataka Matsuura, and Tomio Wada,[56] then improved in by a Sharp team consisting of Kohei Kishi, Hirosaku Nonomura, Keiichiro Shimizu, and Tomio Wada.[57] However, these TFT-LCDs were not yet ready for use in products, as problems with the materials for the TFTs were not yet solved.
[
edit
]
In , researchers at Brown, Boveri & Cie (BBC) Research Center, Switzerland, invented the super-twisted nematic (STN) structure for passive matrix-addressed LCDs. H. Amstutz et al. were listed as inventors in the corresponding patent applications filed in Switzerland on July 7, , and October 28, . Patents were granted in Switzerland CH , Europe EP ,[58] U.S. patent 4,634,229 and many more countries. In , Brown Boveri started a 50/50 joint venture with the Dutch Philips company, called Videlec.[59] Philips had the required know-how to design and build integrated circuits for the control of large LCD panels. In addition, Philips had better access to markets for electronic components and intended to use LCDs in new product generations of hi-fi, video equipment and telephones. In , Philips researchers Theodorus Welzen and Adrianus de Vaan invented a video speed-drive scheme that solved the slow response time of STN-LCDs, enabling high-resolution, high-quality, and smooth-moving video images on STN-LCDs.[citation needed] In , Philips inventors Theodorus Welzen and Adrianus de Vaan solved the problem of driving high-resolution STN-LCDs using low-voltage (CMOS-based) drive electronics, allowing the application of high-quality (high resolution and video speed) LCD panels in battery-operated portable products like notebook computers and mobile phones.[60] In , Philips acquired 100% of the Videlec AG company based in Switzerland. Afterwards, Philips moved the Videlec production lines to the Netherlands. Years later, Philips successfully produced and marketed complete modules (consisting of the LCD screen, microphone, speakers etc.) in high-volume production for the booming mobile industry.
The first color LCD televisions were developed as handheld televisions in Japan. In , Hattori Seiko's R&D group began development on color LCD pocket televisions.[61] In , Seiko Epson released the first LCD television, the Epson TV Watch, a wristwatch equipped with a small active-matrix LCD television.[62][63] Sharp Corporation introduced dot matrix TN-LCD in .[52] In , Epson released the ET-10, the first full-color, pocket LCD television.[64] The same year, Citizen Watch,[65] introduced the Citizen Pocket TV,[61] a 2.7-inch color LCD TV,[65] with the first commercial TFT LCD.[61] In , Sharp demonstrated a 14-inch, active-matrix, full-color, full-motion TFT-LCD. This led to Japan launching an LCD industry, which developed large-size LCDs, including TFT computer monitors and LCD televisions.[66] Epson developed the 3LCD projection technology in the s, and licensed it for use in projectors in .[67] Epson's VPJ-700, released in January , was the world's first compact, full-color LCD projector.[63]
[
edit
]
In , under different titles, inventors conceived electro optical effects as alternatives to twisted nematic field effect LCDs (TN- and STN- LCDs). One approach was to use interdigital electrodes on one glass substrate only to produce an electric field essentially parallel to the glass substrates.[68][69] To take full advantage of the properties of this In Plane Switching (IPS) technology further work was needed. After thorough analysis, details of advantageous embodiments are filed in Germany by Guenter Baur et al. and patented in various countries.[70][71] The Fraunhofer Institute ISE in Freiburg, where the inventors worked, assigns these patents to Merck KGaA, Darmstadt, a supplier of LC substances. In , shortly thereafter, engineers at Hitachi work out various practical details of the IPS technology to interconnect the thin-film transistor array as a matrix and to avoid undesirable stray fields in between pixels.[72][73] The first wall-mountable LCD TV was introduced by Sharp Corporation in .[74]
Hitachi also improved the viewing angle dependence further by optimizing the shape of the electrodes (Super IPS). NEC and Hitachi become early manufacturers of active-matrix addressed LCDs based on the IPS technology. This is a milestone for implementing large-screen LCDs having acceptable visual performance for flat-panel computer monitors and television screens. In , Samsung developed the optical patterning technique that enables multi-domain LCD. Multi-domain and In Plane Switching subsequently remain the dominant LCD designs through .[75] In the late s, the LCD industry began shifting away from Japan, towards South Korea and Taiwan,[66] and later on towards China.
[
edit
]
In the image quality of LCD televisions surpassed the image quality of cathode-ray-tube-based (CRT) TVs.[76] In the fourth quarter of , LCD televisions surpassed CRT TVs in worldwide sales for the first time.[77] LCD TVs were projected to account 50% of the 200 million TVs to be shipped globally in , according to Displaybank.[78][79]
[
edit
]
In October , Toshiba announced × pixels on a 6.1-inch (155 mm) LCD panel, suitable for use in a tablet computer,[80] especially for Chinese character display. The s also saw the wide adoption of TGP (Tracking Gate-line in Pixel), which moves the driving circuitry from the borders of the display to in between the pixels, allowing for narrow bezels.[81]
In , Panasonic developed IPS LCDs with a contrast ratio of 1,000,000:1, rivaling OLEDs. This technology was later put into mass production as dual layer, dual panel or LMCL (Light Modulating Cell Layer) LCDs. The technology uses 2 liquid crystal layers instead of one, and may be used along with a mini-LED backlight and quantum dot sheets.[82][83]
LCDs with quantum dot enhancement film or quantum dot color filters were introduced from to . Quantum dots receive blue light from a backlight and convert it to light that allows LCD panels to offer better color reproduction.[84][85][86][87][88][89] Quantum dot color filters are manufactured using photoresists containing quantum dots instead of colored pigments,[90] and the quantum dots can have a special structure to improve their application onto the color filter. Quantum dot color filters offer superior light transmission over quantum dot enhancement films.[91]
[
edit
]
LCDs do not produce light on their own, so they require external light to produce a visible image.[92][93] In a transmissive type of LCD, the light source is provided at the back of the glass stack and is called a backlight. Active-matrix LCDs are almost always backlit.[94][95] Passive LCDs may be backlit but many are reflective as they use a reflective surface or film at the back of the glass stack to utilize ambient light. Transflective LCDs combine the features of a backlit transmissive display and a reflective display.
The common implementations of LCD backlight technology are:
18 parallel CCFLs as backlight for a 42-inch (106 cm) LCD TV[
96]
[
97]
) then spreads the light out evenly across the whole display. For many years, this technology had been used almost exclusively. Unlike white LEDs, most CCFLs have an even-white spectral output resulting in better color gamut for the display. However, CCFLs are less energy efficient than LEDs and require a somewhat costly inverter to convert whatever DC voltage the device uses (usually 5 or 12 V) to &#; V needed to light a CCFL.[
98]
The thickness of the inverter transformers also limits how thin the display can be made.[
96]
As of , this design is the most popular one in desktop computer monitors. It allows for the thinnest displays. Some LCD monitors using this technology have a feature called dynamic contrast, invented by Philips researchers Douglas Stanton, Martinus Stroomer and Adrianus de Vaan[
99]
Using PWM (pulse-width modulation, a technology where the intensity of the LEDs are kept constant, but the brightness adjustment is achieved by varying a time interval of flashing these constant light intensity light sources[
100]
), the backlight is dimmed to the brightest color that appears on the screen while simultaneously boosting the LCD contrast to the maximum achievable levels, allowing the :1 contrast ratio of the LCD panel to be scaled to different light intensities, resulting in the ":1" contrast ratios seen in the advertising on some of these monitors. Since computer screen images usually have full white somewhere in the image, the backlight will usually be at full intensity, making this "feature" mostly a marketing gimmick for computer monitors, however for TV screens it drastically increases the perceived contrast ratio and dynamic range, improves the viewing angle dependency and drastically reducing the power consumption of conventional LCD televisions.[
101]
[
102]
[
103]
[
104]
While displays lit with white LEDs usually have a poorer color gamut than CCFL lit displays, panels lit with RGB LEDs have very wide color gamuts. This implementation is most popular on professional graphics editing LCDs. As of , LCDs in this category usually cost more than $. As of the cost of this category has drastically reduced and such LCD televisions obtained same price levels as the former 28" (71 cm) CRT based categories.[
105]
[
106]
[
107]
Today, most LCD screens are being designed with an LED backlight instead of the traditional CCFL backlight, while that backlight is dynamically controlled with the video information (dynamic backlight control). The combination with the dynamic backlight control, invented by Philips researchers Douglas Stanton, Martinus Stroomer and Adrianus de Vaan, simultaneously increases the dynamic range of the display system (also marketed as HDR, high dynamic range television or FLAD, full-area local area dimming).[108][109][99]
The LCD backlight systems are made highly efficient by applying optical films such as prismatic structure (prism sheet) to gain the light into the desired viewer directions and reflective polarizing films that recycle the polarized light that was formerly absorbed by the first polarizer of the LCD (invented by Philips researchers Adrianus de Vaan and Paulus Schaareman),[110] generally achieved using so called DBEF films manufactured and supplied by 3M.[111] Improved versions of the prism sheet have a wavy rather than a prismatic structure, and introduce waves laterally into the structure of the sheet while also varying the height of the waves, directing even more light towards the screen and reducing aliasing or moiré between the structure of the prism sheet and the subpixels of the LCD. A wavy structure is easier to mass-produce than a prismatic one using conventional diamond machine tools, which are used to make the rollers used to imprint the wavy structure into plastic sheets, thus producing prism sheets.[112] A diffuser sheet is placed on both sides of the prism sheet to distribute the light of the backlight uniformly, while a mirror is placed behind the light guide plate to direct all light forwards. The prism sheet with its diffuser sheets are placed on top of the light guide plate.[113][96] The DBEF polarizers consist of a large stack of uniaxial oriented birefringent films that reflect the former absorbed polarization mode of the light.[114]
DBEF polarizers using uniaxial oriented polymerized liquid crystals (birefringent polymers or birefringent glue) were invented in by Philips researchers Dirk Broer, Adrianus de Vaan and Joerg Brambring.[115] The combination of such reflective polarizers, and LED dynamic backlight control[99] make today's LCD televisions far more efficient than the CRT-based sets, leading to a worldwide energy saving of 600 TWh (), equal to 10% of the electricity consumption of all households worldwide or equal to 2 times the energy production of all solar cells in the world.[116][117]
[
edit
]
A pink elastomeric connector mating an LCD panel to circuit board traces, shown next to a centimeter-scale ruler. The conductive and insulating layers in the black stripe are very small.A standard television receiver screen, a modern LCD panel, has over six million pixels, and they are all individually powered by a wire network embedded in the screen. The fine wires, or pathways, form a grid with vertical wires across the whole screen on one side of the screen and horizontal wires across the whole screen on the other side of the screen. To this grid each pixel has a positive connection on one side and a negative connection on the other side. So the total amount of wires needed for a p display is 3 x going vertically and going horizontally for a total of wires horizontally and vertically. That's three for red, green and blue and columns of pixels for each color for a total of wires going vertically and rows of wires going horizontally. For a panel that is 28.8 inches (73 centimeters) wide, that means a wire density of 200 wires per inch along the horizontal edge.
The LCD panel is powered by LCD drivers that are carefully matched up with the edge of the LCD panel at the factory level. The drivers may be installed using several methods, the most common of which are COG (Chip-On-Glass) and TAB (Tape-automated bonding) These same principles apply also for smartphone screens that are much smaller than TV screens.[118][119][120] LCD panels typically use thinly-coated metallic conductive pathways on a glass substrate to form the cell circuitry to operate the panel. It is usually not possible to use soldering techniques to directly connect the panel to a separate copper-etched circuit board. Instead, interfacing is accomplished using anisotropic conductive film or, for lower densities, elastomeric connectors.
Prototype of a passive-matrix STN-LCD with 540×270 pixels, Brown Boveri Research, Switzerland,Monochrome and later color passive-matrix LCDs were standard in most early laptops (although a few used plasma displays[121][122]) and the original Nintendo Game Boy[123] until the mid-s, when color active-matrix became standard on all laptops. The commercially unsuccessful Macintosh Portable (released in ) was one of the first to use an active-matrix display (though still monochrome). Passive-matrix LCDs are still used in the s for applications less demanding than laptop computers and TVs, such as inexpensive calculators. In particular, these are used on portable devices where less information content needs to be displayed, lowest power consumption (no backlight) and low cost are desired or readability in direct sunlight is needed.
A comparison between a blank passive-matrix display (top) and a blank active-matrix display (bottom). A passive-matrix display can be identified when the blank background is more grey in appearance than the crisper active-matrix display, fog appears on all edges of the screen, and while pictures appear to be fading on the screen.Displays having a passive-matrix structure use super-twisted nematic STN (invented by Brown Boveri Research Center, Baden, Switzerland, in ; scientific details were published[124]) or double-layer STN (DSTN) technology (the latter of which addresses a color-shifting problem with the former), and color-STN (CSTN), in which color is added by using an internal color filter. STN LCDs have been optimized for passive-matrix addressing. They exhibit a sharper threshold of the contrast-vs-voltage characteristic than the original TN LCDs. This is important, because pixels are subjected to partial voltages even while not selected. Crosstalk between activated and non-activated pixels has to be handled properly by keeping the RMS voltage of non-activated pixels below the threshold voltage as discovered by Peter J. Wild in ,[125] while activated pixels are subjected to voltages above threshold (the voltages according to the "Alt & Pleshko" drive scheme).[126] Driving such STN displays according to the Alt & Pleshko drive scheme require very high line addressing voltages. Welzen and de Vaan invented an alternative drive scheme (a non "Alt & Pleshko" drive scheme) requiring much lower voltages, such that the STN display could be driven using low voltage CMOS technologies.[60] White-on-blue LCDs are STN and can use a blue polarizer, or birefringence which gives them their distinctive appearance.[127][128][129]
STN LCDs have to be continuously refreshed by alternating pulsed voltages of one polarity during one frame and pulses of opposite polarity during the next frame. Individual pixels are addressed by the corresponding row and column circuits. This type of display is called passive-matrix addressed, because the pixel must retain its state between refreshes without the benefit of a steady electrical charge. As the number of pixels (and, correspondingly, columns and rows) increases, this type of display becomes less feasible. Slow response times and poor contrast are typical of passive-matrix addressed LCDs with too many pixels and driven according to the "Alt & Pleshko" drive scheme. Welzen and de Vaan also invented a non RMS drive scheme enabling to drive STN displays with video rates and enabling to show smooth moving video images on an STN display.[citation needed] Citizen, among others, licensed these patents and successfully introduced several STN based LCD pocket televisions on the market.[citation needed]
How an LCD works using an active-matrix structureBistable LCDs do not require continuous refreshing. Rewriting is only required for picture information changes. In HA van Sprang and AJSM de Vaan invented an STN type display that could be operated in a bistable mode, enabling extremely high resolution images up to lines or more using only low voltages.[130] Since a pixel may be either in an on-state or in an off state at the moment new information needs to be written to that particular pixel, the addressing method of these bistable displays is rather complex, a reason why these displays did not make it to the market. That changed when in the "zero-power" (bistable) LCDs became available. Potentially, passive-matrix addressing can be used with devices if their write/erase characteristics are suitable, which was the case for ebooks which need to show still pictures only. After a page is written to the display, the display may be cut from the power while retaining readable images. This has the advantage that such ebooks may be operated for long periods of time powered by only a small battery.
High-resolution color displays, such as modern LCD computer monitors and televisions, use an active-matrix structure. A matrix of thin-film transistors (TFTs) is added to the electrodes in contact with the LC layer. Each pixel has its own dedicated transistor, allowing each column line to access one pixel. When a row line is selected, all of the column lines are connected to a row of pixels and voltages corresponding to the picture information are driven onto all of the column lines. The row line is then deactivated and the next row line is selected. All of the row lines are selected in sequence during a refresh operation. Active-matrix addressed displays look brighter and sharper than passive-matrix addressed displays of the same size, and generally have quicker response times, producing much better images. Sharp produces bistable reflective LCDs with a 1-bit SRAM cell per pixel that only requires small amounts of power to maintain an image.[131]
Segment LCDs can also have color by using Field Sequential Color (FSC LCD). This kind of displays have a high speed passive segment LCD panel with an RGB backlight. The backlight quickly changes color, making it appear white to the naked eye. The LCD panel is synchronized with the backlight. For example, to make a segment appear red, the segment is only turned ON when the backlight is red, and to make a segment appear magenta, the segment is turned ON when the backlight is blue, and it continues to be ON while the backlight becomes red, and it turns OFF when the backlight becomes green. To make a segment appear black, the segment is always turned ON. An FSC LCD divides a color image into 3 images (one Red, one Green and one Blue) and it displays them in order. Due to persistence of vision, the 3 monochromatic images appear as one color image. An FSC LCD needs an LCD panel with a refresh rate of 180 Hz, and the response time is reduced to just 5 milliseconds when compared with normal STN LCD panels which have a response time of 16 milliseconds.[132][133] FSC LCDs contain a Chip-On-Glass driver IC can also be used with a capacitive touchscreen. This technique can also be applied in displays meant to show images, as it can offer higher light transmission and thus potential for reduced power consumption in the backlight due to omission of color filters in LCDs.[134]
Samsung introduced UFB (Ultra Fine & Bright) displays back in , utilized the super-birefringent effect. It has the luminance, color gamut, and most of the contrast of a TFT-LCD, but only consumes as much power as an STN display, according to Samsung. It was being used in a variety of Samsung cellular- models produced until late , when Samsung stopped producing UFB displays. UFB displays were also used in certain models of LG mobile phones.
[
edit
]
Structure of a color LCD with an edge-lit CCFL backlightORIC Electronics contains other products and information you need, so please check it out.
Twisted nematic (TN)[
edit
]
Twisted nematic displays contain liquid crystals that twist and untwist at varying degrees to allow light to pass through. When no voltage is applied to a TN liquid crystal cell, polarized light passes through the 90-degrees twisted LC layer. In proportion to the voltage applied, the liquid crystals untwist changing the polarization and blocking the light's path. By properly adjusting the level of the voltage almost any gray level or transmission can be achieved.
In-plane switching (IPS)[
edit
]
In-plane switching is an LCD technology that aligns the liquid crystals in a plane parallel to the glass substrates. In this method, the electrical field is applied through opposite electrodes on the same glass substrate, so that the liquid crystals can be reoriented (switched) essentially in the same plane, although fringe fields inhibit a homogeneous reorientation. This requires two transistors for each pixel instead of the single transistor needed for a standard thin-film transistor (TFT) display. The IPS technology is used in everything from televisions, computer monitors, and even wearable devices, especially almost all LCD smartphone panels are IPS/FFS mode. IPS displays belong to the LCD panel family screen types. The other two types are VA and TN. Before LG Enhanced IPS was introduced in by Hitachi as 17" monitor in Market, the additional transistors resulted in blocking more transmission area, thus requiring a brighter backlight and consuming more power, making this type of display less desirable for notebook computers. Panasonic Himeji G8.5 was using an enhanced version of IPS, also LGD in Korea, then currently the world biggest LCD panel manufacture BOE in China is also IPS/FFS mode TV panel.
A close-up of a corner of an IPS LCD panel Super In-plane switching (S-IPS)[
edit
]
Super-IPS was later introduced after in-plane switching with even better response times and color reproduction.[135]
M+ or RGBW controversy[
edit
]
In LG Display announced the implementation of a new technology called M+ which is the addition of white subpixel along with the regular RGB dots in their IPS panel technology.[136]
Most of the new M+ technology was employed on 4K TV sets which led to a controversy after tests showed that the addition of a white sub pixel replacing the traditional RGB structure had also been accompanied by a reduction in resolution by around 25%. This meant that a "4K" M+ TV would not display the full UHD TV standard. The media and internet users called them "RGBW" TVs because of the white sub pixel. Although LG Display has developed this technology for use in notebook display, outdoor and smartphones, it became more popular in the TV market because of the announced "4K UHD" resolution but still being incapable of achieving true UHD resolution defined by the CTA as x active pixels with 8-bit color. This negatively impacted the rendering of text, making it a bit fuzzier, which was especially noticeable when a TV is used as a PC monitor.[137][138][139][140]
[
edit
]
In , LG claimed the smartphone LG Optimus Black (IPS LCD (LCD NOVA)) has the brightness up to 700 nits, while the competitor has only IPS LCD with 518 nits and double an active-matrix OLED (AMOLED) display with 305 nits. LG also claimed the NOVA display to be 50 percent more efficient than regular LCDs and to consume only 50 percent of the power of AMOLED displays when producing white on screen.[141] When it comes to contrast ratio, AMOLED display still performs best due to its underlying technology, where the black levels are displayed as pitch black and not as dark gray. On August 24, , Nokia announced the Nokia 701 and also made the claim of the world's brightest display at nits. The screen also had Nokia's Clearblack layer, improving the contrast ratio and bringing it closer to that of the AMOLED screens.
This pixel layout is found in S-IPS LCDs. A chevron shape is used to widen the viewing cone (range of viewing directions with good contrast and low color shift). Advanced fringe field switching (AFFS)[
edit
]
Known as fringe field switching (FFS) until ,[142] advanced fringe field switching is similar to IPS or S-IPS offering superior performance and color gamut with high luminosity. AFFS was developed by Hydis Technologies Co., Ltd, Korea (formally Hyundai Electronics, LCD Task Force).[143] AFFS-applied notebook applications minimize color distortion while maintaining a wider viewing angle for a professional display. Color shift and deviation caused by light leakage is corrected by optimizing the white gamut which also enhances white/gray reproduction. In , Hydis Technologies Co., Ltd licensed AFFS to Japan's Hitachi Displays. Hitachi is using AFFS to manufacture high-end panels. In , HYDIS licensed AFFS to Sanyo Epson Imaging Devices Corporation. Shortly thereafter, Hydis introduced a high-transmittance evolution of the AFFS display, called HFFS (FFS+). Hydis introduced AFFS+ with improved outdoor readability in . AFFS panels are mostly utilized in the cockpits of latest commercial aircraft displays. However, it is no longer produced as of February .[144][145][146]
Vertical alignment (VA)[
edit
]
Vertical-alignment displays are a form of LCDs in which the liquid crystals naturally align vertically to the glass substrates. When no voltage is applied, the liquid crystals remain perpendicular to the substrate, creating a black display between crossed polarizers. When voltage is applied, the liquid crystals shift to a tilted position, allowing light to pass through and create a gray-scale display depending on the amount of tilt generated by the electric field. It has a deeper-black background, a higher contrast ratio, a wider viewing angle, and better image quality at extreme temperatures than traditional twisted-nematic displays.[147] Compared to IPS, the black levels are still deeper, allowing for a higher contrast ratio, but the viewing angle is narrower, with color and especially contrast shift being more apparent, and the cost of VA is lower than IPS (but higher than TN).[148]
[
edit
]
Blue phase mode LCDs have been shown as engineering samples early in , but they are not in mass-production. The physics of blue phase mode LCDs suggest that very short switching times (&#;1 ms) can be achieved, so time sequential color control can possibly be realized and expensive color filters would be obsolete.[citation needed]
[
edit
]
Some LCD panels have defective transistors, causing permanently lit or unlit pixels which are commonly referred to as stuck pixels or dead pixels respectively. Unlike integrated circuits (ICs), LCD panels with a few defective transistors are usually still usable. Manufacturers' policies for the acceptable number of defective pixels vary greatly. At one point, Samsung held a zero-tolerance policy for LCD monitors sold in Korea.[149] As of , Samsung adheres to the less restrictive ISO -2 standard.[150] Other companies have been known to tolerate as many as 11 dead pixels in their policies.[151]
Dead pixel policies are often hotly debated between manufacturers and customers. To regulate the acceptability of defects and to protect the end user, ISO released the ISO -2 standard, which was made obsolete in with the release of ISO , specifically ISO--302, 303, 305, 307: pixel defects. However, not every LCD manufacturer conforms to the ISO standard and the ISO standard is quite often interpreted in different ways. LCD panels are more likely to have defects than most ICs due to their larger size.[152]
Some manufacturers, notably in South Korea where some of the largest LCD panel manufacturers, such as LG, are located, now have a zero-defective-pixel guarantee, which is an extra screening process which can then determine "A"- and "B"-grade panels.[original research?] Many manufacturers would replace a product even with one defective pixel. Even where such guarantees do not exist, the location of defective pixels is important. A display with only a few defective pixels may be unacceptable if the defective pixels are near each other. LCD panels also commonly have a defect known as clouding, dirty screen effect, or, less commonly, mura, which involves uneven patches of luminance on the panel. It is most visible in dark or black areas of displayed scenes.[153] As of , most premium branded computer LCD panel manufacturers specify their products as having zero defects.
"Zero-power" (bistable) displays[
edit
]
The zenithal bistable device (ZBD), developed by Qinetiq (formerly DERA), can retain an image without power. The crystals may exist in one of two stable orientations ("black" and "white") and power is only required to change the image. ZBD Displays is a spin-off company from QinetiQ who manufactured both grayscale and color ZBD devices. Kent Displays has also developed a "no-power" display that uses polymer stabilized cholesteric liquid crystal (ChLCD). In Kent demonstrated the use of a ChLCD to cover the entire surface of a mobile , allowing it to change colors, and keep that color even when power is removed.[154]
In , researchers at the University of Oxford demonstrated two new types of zero-power bistable LCDs based on Zenithal bistable techniques.[155] Several bistable technologies, like the 360° BTN and the bistable cholesteric, depend mainly on the bulk properties of the liquid crystal (LC) and use standard strong anchoring, with alignment films and LC mixtures similar to the traditional monostable materials. Other bistable technologies, e.g., BiNem technology, are based mainly on the surface properties and need specific weak anchoring materials.
[
edit
]
[
156]
But a lower refresh rate can mean visual artefacts like ghosting or smearing, especially with fast moving images. Individual pixel response time is also important, as all displays have some inherent latency in displaying an image which can be large enough to create visual artifacts if the displayed image changes rapidly.[
157]
There are additional aspects to LCD color and color management, such as white point and gamma correction, which describe what color white is and how the other colors are displayed relative to white.[
edit
]
Some of these issues relate to full-screen displays, others to small displays as on watches, etc. Many of the comparisons are with CRT displays.
[
edit
]
[
edit
]
[
edit
]
Several different families of liquid crystals are used in liquid crystal displays. The molecules used have to be anisotropic, and to exhibit mutual attraction. Polarizable rod-shaped molecules (biphenyls, terphenyls, etc.) are common. A common form is a pair of aromatic benzene rings, with a nonpolar moiety (pentyl, heptyl, octyl, or alkyl oxy group) on one end and polar (nitrile, halogen) on the other. Sometimes the benzene rings are separated with an acetylene group, ethylene, CH=N, CH=NO, N=N, N=NO, or ester group. In practice, eutectic mixtures of several chemicals are used, to achieve wider temperature operating range (&#;10..+60 °C for low-end and &#;20..+100 °C for high-performance displays). For example, the E7 mixture is composed of three biphenyls and one terphenyl: 39 wt.% of 4'-pentyl[1,1'-biphenyl]-4-carbonitrile (nematic range 24..35 °C), 36 wt.% of 4'-heptyl[1,1'-biphenyl]-4-carbonitrile (nematic range 30..43 °C), 16 wt.% of 4'-octoxy[1,1'-biphenyl]-4-carbonitrile (nematic range 54..80 °C), and 9 wt.% of 4-pentyl[1,1':4',1-terphenyl]-4-carbonitrile (nematic range 131..240 °C).[172]
[
edit
]
The production of LCD screens uses nitrogen trifluoride (NF3) as an etching fluid during the production of the thin-film components. NF3 is a potent greenhouse gas, and its relatively long half-life may make it a potentially harmful contributor to global warming. A report in Geophysical Research Letters suggested that its effects were theoretically much greater than better-known sources of greenhouse gasses like carbon dioxide. As NF3 was not in widespread use at the time, it was not made part of the Kyoto Protocol and was deemed "the missing greenhouse gas".[173] NF3 was added to the Kyoto Protocol for the second compliance period during the Doha Round.[174]
Critics of the report point out that it assumes that all of the NF3 produced would be released to the atmosphere. In reality, the vast majority of NF3 is broken down during the cleaning processes; two earlier studies found that only 2 to 3% of the gas escapes destruction after its use.[175] Furthermore, the report failed to compare NF3's effects with what it replaced, perfluorocarbon, another powerful greenhouse gas, of which anywhere from 30 to 70% escapes to the atmosphere in typical use.[175]
[
edit
]
[
edit
]
[
edit
]
Author: Adam Simmons
Last updated: September 26th
Introduction
Most people are familiar with the fact that monitors come in various resolutions and screen sizes, can have a matte or glossy screen surface and can offer specific features such as 120Hz refresh rates and 3D capabilities. The range of displays and variation in specification can be rather daunting and what&#;s more; you can&#;t necessarily trust the &#;on paper&#; figures in the first place. One fundamentally important aspect of an LCD monitor which will dictate how it performs and what kind of tasks it would be best at performing is the panel type. Although there are various sub-divisions all modern screens will generally fall into one of three categories with distinct performance characteristics.
As an Amazon Associate I earn from qualifying purchases made using the below link. Where possible, you&#;ll be redirected to your nearest store. Further information on supporting our work.
Buy from Amazon
Until fairly recently the TN panel monitor has been the most ubiquitous on the market. Manufacturers will often be keen to point out in their specifications whether an &#;alternative&#; kind of panel is used; if in doubt assume its TN. General attributes include a relatively low manufacturing cost and a relatively high level of responsiveness; the pixels change their state quickly which helps make moving images appear smoother. Some Twisted Nematic displays have double the usual refresh rate (120Hz instead of 60Hz) allowing them to take advantage of &#;active 3D shutter&#; technologies and allowing them to display twice as much information every second for a smoother gaming experience. This has gone further now, with more recent releases featuring a 144Hz or higher refresh rate and aiming this purely at a fluid 2D rather than 3D (stereoscopic glasses) experience.
Although it has improved leaps and bounds in this department over the years the image performance is often considered a relative weakness of TN technology. A good TN monitor can provide a crisp and vibrant image with respectable contrast &#; typically :1 with any &#;dynamic contrast&#; mode disabled. The main drawback comes with relatively restricted viewing angles. These are often quoted as 170° horizontal and 160° vertical which is only marginally lower than that quoted for other panel technologies. In actuality you will see a marked change in colour and even &#;inversion&#; if you view the screen from the side but also from above or below, in particular. You can see this shift demonstrated in this video taken using what is regarded as one of the more capable TN monitors (the Dell SDGF).
Particularly but not exclusively on larger TN models, the relatively restricted viewing angles actually affect the performance if you are sitting directly in front as well. Your eyes subtend different viewing angles if you observe the centre of the screen compared to observing peripheral regions. You will see a given shade represented differently depending on its position on the screen &#; most notably being darker (more saturated and higher perceived gamma) towards the top of the screen and lighter (less saturated and lower perceived gamma) towards the bottom. Because of this, the colour accuracy and consistency suffers making them a poor choice for &#;colour critical work&#; such as design and photography. You can see this in the image below, captured on the ASUS PG278Q in a way that is fairly representative of what you would see when observing the monitor from a normal viewing position at a desk. These shifts in perceived gamma and saturation are greater if you sit closer to the screen.
The image below shows the Dell SDG, another TN model, displaying the Datacolor SpyderCHECKR 24 test patches. There is a printed sheet of shades, all of which are contained within the sRGB colour space. The screen is displaying a reference photograph of the printed shade board, provided by Datacolor. This should match the printed shade quite closely if the monitor is accurately outputting shades within the sRGB colour space. Although there is always some disparity between how emissive objects (monitor) and non-emissive objects (printed sheet) appear. The shades are displayed in the same order as the printed sheet on the right of the screen, whilst the order is inverted on the left side of the screen. Whilst the exact shades you see will differ from those you&#;d see in real life, due to the camera used and the screen you&#;re viewing this photo on, it still gives a good idea of the relative differences. It also provides a very clear visual demonstration of the colour consistency issues described earlier. The light chocolate brown shade and golden yellow (gamboge) shade next to it, for example, look far deeper when displayed near the top of the screen. The golden yellow shade is actually a fairly close match to the printed shade at this point. When displayed near the bottom, the brown shade appears far more clay-like. And the golden yellow a brighter yellow shade, more closely matching the other yellow shade on the printed sheet. The shades have what should be a very subtle texture to them due to the material they&#;re printed on. This is captured in the reference photographs and is most obvious for the black block. It&#;s brought out far too strongly when the shade is displayed lower down the screen and is much better-blended when it&#;s displayed further up the screen, due to the perceived gamma shifts.
If an LCD monitor is trying to display black then the colour filter will be positioned such that as little light as possible (of any colour) from the backlight will get through. Most LCD monitors will do a reasonable job at this but the filter isn&#;t perfect and so the blacks may not appear as deep as they should. A definite strength of the VA panel is its efficiency at blocking light from the backlight when it&#;s not wanted. This gives deeper blacks and higher contrast ratios of around :1 &#; :1 with &#;Dynamic Contrast&#; modes disabled &#; several times higher than that of the other LCD technologies. This can have a positive effect by giving a more atmospheric look to dark scenes in games and movies, whilst adding definition and depth to shadows and other fine details in the image. VA models can also provide a relatively solid or &#;inky&#; appearance to some medium shades, particularly when compared to models with significantly weaker contrast. They&#;re also less susceptible to &#;bleed&#; or &#;clouding&#; towards the edges of the screen, which can make such screens good candidates for movie lovers and nice to use for general purpose work. Such issues still can, unfortunately, still plague some units of any panel type and tend to be more common with the curved VA panels many manufacturers are now pushing.
Another key advantage of VA is the improved viewing angles and colour reproduction compared to TN. The shift in colour across the screen and &#;off angle&#; is less pronounced, whilst shades can be produced with greater precision. In this respect they are better candidates for colour critical work, but they are not as strong in this area as the IPS and related technologies explored subsequently. There is a weakening of saturation when comparing a shade in the centre of the screen vs. that same shade towards the edges or bottom of the screen, from a normal viewing position. This loss of saturation can also be observed further up the screen, particularly on larger screens or if your eyes are in line with the centre of the screen or below. There&#;s also a shift in gamma that is most noticeable on greys or pastel shades but can also be observed elsewhere, with said shade appearing to lighten or darken quite readily with even slight head movement. Some VA models almost have a &#;cone&#; or &#;tunnel&#; effect due to these shifts, with the peripheral regions appearing noticeably duller than the central mass of the screen. This also masks dark detail centrally (&#;black crush&#;, high perceived gamma) and can reveal extra unintended detail peripherally (low perceived gamma). The image shows the same SpyderCHECKR 24 system used for the TN example earlier, this time on the AOC PD27 with VA panel. The vertical shifts in saturation and colour representation are less extreme, but certainly still there. These gamma and saturation shifts are more pronounced if you sit closer to the screen or if the screen is larger.
Some of the modern VA panel types used on PC monitors include SVA (&#;Super&#; Vertical Alignment), MVA (Multi-domain Vertical Alignment) and AAS (Azimuthal Anchoring Switch) VA-type panels. Regardless of the panel technology used, a common weakness with many VA models is with their slow pixel responses for some transitions. In some severe cases things can appear as &#;smoke-like&#; trails. Recent models using AU Optronics VA, CSOT VA and Samsung SVA panels generally use effective pixel overdrive and don&#;t suffer from widespread &#;smoke-like&#; trails. They are actually on par with modern IPS models for some pixel transitions, which is something manufacturers will latch onto by giving misleading and overly optimistic specified response times. 4ms is commonly specified, as some pixel transitions can be expected to be performed at this kind of speed. Other pixel transitions, particularly where darker shades are involved in the transition, are still relatively slow. Enough to significantly increase perceived blur with some &#;smeary&#; trailing &#; generally falling short of &#;smoke-like&#; in appearance, but still extending quite far from the object during motion. The video section below shows some nice visual examples of such trailing from our Gigabyte G32QC review.
There has been an increasing drive towards high refresh rate VA panels, including 34&#;- 35&#; UltraWide VA panels with 100Hz+ refresh rates and various sizes of screen with 144Hz+ 16:9 VA panels. Models such as the AOC C24G1 and LG 32GK850G employ effective and flexible pixel overdrive and can deliver a reasonable 144Hz &#; 165Hz experience. Users benefit from the decreased perceived blur of running the high refresh rate at suitably high frame rates, with many pixel transitions performed fast enough for a decent performance there. But there are still some weaknesses, with some pixel responses substantially slower than optimal and giving some &#;heavy powdery&#; or &#;smeary&#; trailing in places. Some models, including the AOC C24G1, have another trick up their proverbial sleeves. They include strobe backlight modes (called MBR or &#;Motion Blur Reduction&#; on the AOC) which can greatly reduce perceived blur caused by eye movement, provided the frame rate matches the refresh rate. This concept and related aspects are explored in detail in our article on responsiveness.
The pixel response time weaknesses common on VA models can also manifest as a sort of &#;flickering&#; effect or blending together, where some brighter shades appear to darken during movement and blend into neighbouring dark shades. The shade brightness returns to normal when the movement ceases. There is a demonstration of this effect on the AOC PD27 in game and also on the desktop on our video review of that model. That&#;s actually a relatively fast VA model, but there are still some distinct weaknesses &#; especially at higher refresh rates, where the pixel responses can&#;t keep up with the rigorous requirements there. This can be reduced by increasing the overdrive setting, but that introduces strong overshoot. The video below taken from our AOC CQ32G3SU review also shows this &#;flickering&#; or blending effect.
Only a small handful of VA models deliver rapid enough pixel responses to really avoid these sorts of traditional VA weaknesses at high refresh rates, without strong overshoot. The best examples of that with appropriate data and real-world experiences to back this up are the 240Hz Samsung Odyssey models. With the 27&#; versions being particularly impressive in that respect.
When it comes to the end result these three technologies are essentially very similar; the key differences being that IPS technology is developed chiefly by LG Display, PLS technology by Samsung (no longer manufactured) and AHVA by AUO. These are sometimes simply referred to collectively as &#;IPS-type&#; panels. Other panel manufacturers have their own &#;IPS-type&#; technologies, including Innolux with their AAS (Azimuthal Anchoring Switch) technology &#; which, confusingly, also has VA-type iterations. And BOE with their IPS-ADS technology. The real selling point of these is their superior colour accuracy, consistency and viewing angles when compared to the other LCD technologies. Each shade remains distinct with its own &#;identity&#; regardless of its position on the screen. This is combined with extended colour gamuts (increasing potential shade range and saturation) on some models for a vibrant and saturated look throughout the screen. Gamma consistency is also strong, ensuring dark shades appear largely appropriate throughout the screen rather than appearing too visible in some regions of the screen and far too masked in other regions. This consistency in both gamma and saturation makes IPS-type panels particularly good candidates for &#;colour critical&#; work. Those who appreciate colour-richness that&#;s well-maintained throughout the screen may enjoy using them for gaming, movies and general desktop work as well. The image shows the same SpyderCHECKR 24 system used for the TN and VA examples earlier, this time on the ASUS PA278QV with IPS-type panel. The consistency is far superior to the TN example and improved compared to the VA example as well, with the shade sets on the left and right of the screen appearing relatively similar to one another.
There&#;s a very good range of affordable IPS-type monitors available from most major manufacturers, including Dell, LG, Acer, AOC and ASUS. This means that photographers, designers or just regular users on a lower budget can take advantage of the technology too. Many modern IPS-type monitors are also far more responsive than their VA counterparts and in some cases are effective rivals to many TN monitors. Responsiveness was traditionally an area of significant weakness for IPS panels. Due to dramatic improvements in pixel responsiveness and refresh rate, some modern models have found favour amongst gamers who take advantage of the colour performance in their favourite titles without lots of unsightly trailing. 144Hz+ panels of this type are now common. Another area of traditional weakness was contrast. There have been some improvements there, with most panels of this type similar to their TN counterparts in that department now (around :1 contrast ratio without dynamic contrast). Some are a bit stronger, some a bit weaker. One troublesome issue that some people have noticed is a sheen or &#;glow&#; when viewing dark content that is caused by the behaviour of light in these panels. This is typically most obvious when viewing &#;off angle&#; as shown on the BenQ PDQ in the video below. You will generally be able to observe this on the corners of 21.5&#;+ models whilst viewing from directly in front, unless you are sitting quite far back from the screen. The majority of time you will be looking at brighter and more colourful shades where these displays excel but it is always worth looking beyond figures on paper.
There are three main categories of panel used on modern LCD monitors; TN, VA and IPS-type. Up until quite recently TN was the most prevalent, offering decent image performance and high responsiveness at a decent price. VA sacrifices responsiveness, generally being the slowest current panel type but offering relatively strong contrast and improvements in colour performance over TN technologies. IPS and related technologies are the kings of colour offering the most consistent and accurate performance in this area whilst sporting excellent viewing angles, respectable responsiveness and reasonable contrast. Really it is up to the individual user to weigh up the advantages and disadvantages of the monitors they are comparing; understanding the general performance characteristics of different panels is a great starting point.
Donations are also greatly appreciated.
For more information, please visit bar type lcd.