Steam surface condensers have a crucial role in the operation of power generation plants. Clean condenser tubes lead to increased efficiency of the system and therefore to a higher megawatt production. Goodway Benelux offers an innovative condenser tube cleaning solution for power plants in Europe. In short, a condenser with 10.000 tubes or more could be cleaned in a day or two. This blog explains the importance of a clean condenser, and shares insight into Goodway's condenser cleaning solutions. The blog also includes info, pictures and videos of a recent project in Denmark, where 15.600 condenser tubes had to be cleaned.
Steam surface condensers have thousands of tubes which have a cooling media (river-, sea-, or lake water) flowing through them. The condenser plays a crucial role in the power generating process. The cleaner the tubes, the better the heat transfer will be. The better the heat transfer, the higher the efficiency of the overal plant will be. Furthermore, it will lead to an increased production of megawatt output which means more revenue.
Some power plants have an online ball cleaning system installed on their condenser(s). Small balls flow through the tubes during operation of the condenser, which helps to keep the condenser tubes in decent state. In practice, though, a mechanical cleaning will still be required periodically. These cleaning balls do not choose the tubes that they go in; they are sucked into the tubes that have the highest flow. This means that some tubes will be cleaned more often and better than others. Also, these balls can get stuck in the tubes over time. This creates a blocked tube that has no flow. This ''deadzone'' in the tube can lead to corrosion and oxidation. In short, automatic ball cleaning systems might extend the cleaning interval time, they do certainly not exclude it. Surface condensers will always experience some sort of fouling, some more than others.
Projectile tube cleaning can be explained as follows: special projectiles are shot through condenser tubes at high-speed, with a low-pressure propulsion system. These projectiles remove deposits from the tube wall by scraping it off. One shot is usually enough to get a condenser tube clean. Projectiles are selected based on the (expected) fouling inside the tubes.
Figure: Condenser tubes blocked with seawater deposits, like barnacles. Nylon coil brush projectiles removed all deposits in 1 shot. Cooling water can now flow through these tubes again.
Projectile tube cleaning offers a number of advantages. In many cases, this technique is safer, faster, and more efficient and effective than traditional cleaning, such as high pressure lancing. Below you will find a brief summary of the main benefits:
In , Goodway Benelux was contacted by a 360MW biomass power plant from Denmark. One of their seawater cooled condensers, consisting of 15.600 tubes, was significantly fouled. The condenser is equipped with an automatic, online ball cleaning system, but this wasn&#;t enough to keep the condenser tubes clean over time.
The condenser consists of 2 separate chambers, with 4 rows of tubes per chamber, making it a total of 15.600 tubes. Deposits such as biological fouling, sediment, mussels/barnacles, and a little layer of scale had to be removed, some tubes were completely blocked by the mussels. Nylon coil brush projectiles were used to clean the tubes, and shot through with Goodway&#;s kinetic-hydrostatic pump system (20-30 BAR, 130 l/min waterflow).
Figure: nylon coil brushes loaded in tubes.
To give an idea about the necessary equipment, the plant used a total of 4.000pcs nylon coil brush projectiles (= &#;10.000,-). These could be re-used 4 times, since they had a relatively soft landing on the backside of the condenser tubes.
Goodway Benelux supplied the cleaning equipment, and went over to Denmark for 2 days, to help during start-up. The operators on-site were trained to perform the cleaning themselves. Once they found their rhythm, the operators were able to clean 400-500 tubes per hour. The video hereunder illustrates the cleaning speed.
Goodway Benelux's recommendation for power generation plants is a preventive cleaning and maintenance strategy for the condenser(s). When a mechanical cleaning occurs on a regular basis, deposits will remain soft in most cases, and therefore easy to remove with projectiles. Tubes do not get plugged with hard deposits and softer (nylon) projectiles can be used for the cleaning. This leads to a much easier cleaning process, less risk and lower costs. The costs for cleaning the condenser will be won back very quickly, by just a very minimal increase in efficiency. Ideally, condenser tubes are cleaned once per year, or worst case, once per 2 years.
When tubes are cleaned less often or not at all, the deposits will multiply further and grow into a harder substance. Fouling like limescale could occur, which is not easy to remove. At that point, it could be inevitable to use harder types of projectiles (such as carbon steel scrapers), high pressure cleaning ( BAR or more), or a chemical cleaning with a descaler. This could lead to much higher cleaning costs, more risk, and a much longer downtime of the condenser. Or in other words, a much more complex cleaning operation.
Additionally, fouling in condenser tubes not only negatively impacts the efficiency of the system, but it also poses a threat to the lifetime of the tubes themselves. When fouling is left unchecked for a while, the tubes can become corroded, ultimately leading to damage in the form of leakages. In the industry, this is often referred to as pitting corrosion. This type of damage is usually caused by, either or a joint combination, of under deposit corrosion (UDC) and microbiologically influenced corrosion (MIC). Usually, this form of damage goes unnoticed for a long time because the deposits cover it up - they keep the tube intact. As soon as the deposit (often scale) is removed, the damage will be uncovered. The customer might think that the cleaning technology has created damages inside the tubes, but it has merely uncovered what has been going on for a longer time. A preventive cleaning strategy ensures that deposits are removed as soon as possible, preventing them to grow and cause future problems.
In short, a preventive cleaning and maintenance strategy for power plant condensers pays itself back pretty easily. The condenser tubes remain clean, which increases heat transfer and thus the efficiency of the whole plant. Which down the line creates a higher megawatt production and thus more revenue for the company. Projectile tube cleaning offers a quick, but effective and safe solution to get clean condenser tubes.
Are you interested to learn more about Goodway's projectile tube cleaning technology and equipment? Would you like to discuss if a projectile tube cleaning solution could be interesting for the condenser(s) of your (power) plant?
You can easily reach out to us, either by , , or contact one of our people on LinkedIn. We can answer your questions, share more information, and if some more info is shared on your application, we can have a closer look and come up with a concrete advise how to maintain/clean it.
Click on this link to go to our customer service page and get in touch with us!
Condenser Tube And Heat Exchanger Brushes
Nylon Tube Brushes
Product Description
Condenser tube cleaning brushes are filled with blue nylon bristles and twisted with galvanized steel wire.
Protective tip on the brush head can protect tube walls from sharp scratching.
Wire size 0.10mm, 0.12mm, 0.15mm, 0.20mm, 0.3mm and larger.
Brush end can be assembled with M6 thread or other types.
Brush filaments can be available in carbon steel, stainless steel, brass or nylon bristle.
Brush dimensions and material can be custom made according to your requirement.
With competitive price and timely delivery, FUYI BRUSH sincerely hope to be your supplier and partner.
Product Image
Product Specification
Part
#
Bristle Material
Stem
Material
Thread
Size
Brush
Diameter
D
(mm)
Brush
Length
A
(mm)
Overall
Length
B
(mm)
nylon bristle
stainless steel
M6
3/4" (19.05)
100
160
nylon bristle
stainless steel
M6
7/8" (22.22)
100
160
nylon bristle
stainless steel
M6
1" (25.40)
100
160
* If the brush you required is not listed here, please contact us for further information.
* Brush dimension and materials can be custom made according to your application.
A - Brush Length
B - Overall Length
C - Tip Length
D - Brush Diameter
E - Thread Length
F - Thread Diameter
G - Thread Length
Product Features
- High density of nylon bristle has good cleaning effect
- Sturdy steel wire can be twisted tightly without loose filament
- Brush Handle can resist strong pulling force
- M6 thread can be connected with adapter threads and extension quickly
- Brush dimensions and material can be custom made
Available Brush Head in LikeBrush
Available Brush End in LikeBrush
Production Process
Shipment and Logistics
Customer Question & Answer
1, What is your usual price terms?
2, How about your delivery time ?
3, How about your packing ?
4, How about your payment terms ?
5, What is your miminum order quantity ?
:
MOQ pieces.Contact us to discuss your requirements of condenser tube brushes. Our experienced sales team can help you identify the options that best suit your needs.